# Modified Morris-Lecar model
# based on model used in Prescott et al. Pyramidal neurons switch from integrators in vitro to resonators under in vivo-like conditions. J. Neurophysiol. 2008
# This version of the model includes cumulative sodium channel inactivation
# other parameters have been changed to match those indicated in Fig. 9B of the paper.
#dV/dt = (i_dc+i_noise-gna*minf(V)*(V-Vna)-gk*w*(V-VK)-gshunt*(V-Vshunt)-gM*zM*(v-vk)-gAHP*zAHP*(v-vk))/c
dv/dt = (i_dc+i_noise-gna*h*minf(V)*(V-Vna)-gk*w*(V-VK)-gshunt*(V-Vshunt)-gM*zM*(v-vk)-gAHP*zAHP*(v-vk))/c
dw/dt = phi_w*(winf(V)-w)/tauw(V)
dzAHP/dt = (zinfAHP(v)-zAHP)/tauzAHP
dzM/dt = (zinfM(v)-zM)/tauzM
param c=2
# HERE IS EVERYTHING YOU NEED TO KNOW ABOUT THE STIMULuS
# DC OFFSET
# this is controlled by i_dc
param i_dc=0
# NOISE
# This is modeled as an Ornstein-Uhlenbeck process, gives new noise on each trial
# Here is the Wiener variable
wiener nz
# With scale=0 you get no noise
# effects of changing dt are automatically controlled for in XPP
# However, variance of i_noise also depends on tau_inoise (variance = sigma^2*tau/2)
# Therefore, if you want to keep the same variance, you must manually change sigma_inoise if you change tau_inoise
di_noise/dt=-1/tau_inoise*(i_noise-i_avg)+sigma*nz
param sigma=0, tau_inoise=5, i_avg=0
# increase sigma to include noise; sigma=0.1 in paper
## frozen noise can be repeated on multiple trials by saving i_noise to a .tab file and playing it back
## see xpp documentation about tables
# HERE IS EVERYTHING YOU NEED TO KNOW ABOUT INTRINSIC CURRENTS
# Initial conditions
V(0)=-70
w(0)=0.000025
zAHP(0)=0
zM(0)=0
# if you want to make sure initial conditions are at steady state
# run trial with no stim, then select "initial conditions/last" from main menu... this will start you at the conditions at the end of your previous trial
# FAST INWARD CURRENT (INa or activation variable)
# This is assumed to activate instantaneously with changes in voltage
# voltage-dependent activation curve is described by m
minf(V)=.5*(1+tanh((V-beta_m)/gamma_m))
# maximal conductance and reversal potential
param beta_m=-1.2, gamma_m=18
param gna=24, vna=50
# to implement sodium channel inactivation at steady state, simply reduce gna
# to implement sodium channel inactivation dynamically, comment out line 3 and uncomment line 4, and uncomment the following four lines
dh/dt = (hinf(v)-h)/tau_h
hinf(v)=1-alpha_h/(1+exp((beta_h-v)/gamma_h))
param tau_h=1000,alpha_h=0.67,beta_h=-40,gamma_h=8
h(0)=1
# Following parameters should also be changed (see Fig. 9 in paper): gna=24, gk=30, gamma_w=8, betazM=-29, gammazM=2, tauzM=400, gM=2
# DELAYED RECTIFIER CURRENT (IKdr or recovery variable)
# this current activates more slowly than INa, but is still faster than Isub or Iadapt (not included here)
# In this code, activation of IKdr is controlled by w (equivalent to y in 3D model)
winf(V)=.5*(1+tanh((V-beta_w)/gamma_w))
tauw(V)=1/cosh((V-beta_w)/(2*gamma_w))
# in the 2D model, varying beta_w shifts the w activation curve (w=y here) and can convert the neuron between class 1, 2, and 3
param beta_w=-9, gamma_w=8
# maximal conductance and reversal potential
param gk=30, vk=-100, phi_w=0.25
# SHUNT CURRENT (Ishunt)
# just a passive leak conductance
# gshunt = 2 for low conductance. Increase to 4 for high conductance, i.e. shunting
param gshunt=2, vshunt=-70
# ADAPTATION
# This actually comprises two current, voltage-activated M-type current and calcium-activated AHP current
# The latter is not modelled as calcium-dependent, but with betayAHP = 0, this current is only activated during spikes... roughtly the same conditions under which calcium influx occurs to activate this current
# Because IAHP does not activate at subthreshold voltages, it does not influence subthreshold voltage dynamics.
# Focus on inserting or removing M current by adjusting gM
param tauzM=400
# latter in the paper, tauzM was changed to 400 to get theta-frequency oscillations
zinfM(v)=1/(1+exp((betazM-V)/gammazM))
param betazM=-29,gammazM=2
param gM=2
param tauzAHP=200
zinfAHP(v)=1/(1+exp((betazAHP-V)/gammazAHP))
param betazAHP=0,gammazAHP=5
param gAHP=1
# following parameters control duration of simulation and axes of default plot
@ total=100000,dt=.1,xlo=-100,xhi=60,ylo=-.125,yhi=.6,xp=v,yp=w
@ meth=euler
@ MAXSTOR=1000000
done